Computer Networking
About Lesson

EIGRP (Enhanced Interior Gateway Routing Protocol) is an advanced distance vector routing protocol. This protocol is an evolution of an earlier Cisco protocol called IGRP, which is now considered obsolete. EIGRP supports classless routing and VLSM, route summarization, incremental updates, load balacing and many other useful features. It is a Cisco propriatery protocol, so all routers in a network that is running EIGRP must be Cisco routers.

Routers running EIGRP must become neighbors before exchanging routing information. To dynamically discover neighbors, EIGRP routers use the multicast address of Each EIGRP router stores routing and topology information in three tables:

Neighbor table – stores information about EIGRP neighbors

Topology table – stores routing information learned from neighboring routers

Routing table –  stores the best routes

Administrative distance of EIGRP is 90, which is less than both the administrative distance of RIP and  the administrative distance of OSPF, so EIGRP routes will be preferred over these routes. EIGRP uses Reliable Transport Protocol (RTP) for sending messages.

EIGRP calculates its metric by using bandwidth, delay, reliability and load. By default, only bandwidth and delay are used when calulating metric, while reliability and load are set to zero.

EIGPR uses the concept of autonomous systems. An autonomous system is a set of EIGRP enabled routers that should become EIGRP neighbors. Each router inside an autonomous system must have the same autonomous system number configured, otherwise routers will not become neighbors.

EIGRP Neighbors

EIGRP must establish neighbor relationships with other EIGRP neighboring routers before exchanging routing information. To establish a neighbor relationships, routers send hello packets every couple of seconds. Hello packets are sent to the multicast address of

On LAN interfaces hellos are sent every 5 seconds. On WAN interfaces every 60 seconds.

The following fields in a hello packet must be the identical in order for routers to become neighbors:

ASN (autonomous system number)

subnet number

K values (components of metric)

Routers send hello packets every couple of seconds to ensure that the neighbor relationship is still active. By default, routers considers the neighbor to be down after a hold-down timer has expired. Hold-down timer is, by default, three times the hello interval. On LAN network the hold-down timer  is 15 seconds.

Feasible and reported distance

Two terms that you will often encounter when working with EIGRP are feasible and reported distance. Let’s clarify these terms:

Feasible distance (FD) – the metric of the best route to reach a network. That route will be listed in the routing table.

Reported distance (RD) – the metric advertised by a neighboring router for a specific route. It other words, it is the metric of the route used by the neighboring router to reach the network.

To better understand the concept, consider the following example.

EIGRP has been configured on R1 and R2. R2 is directly connected to the subnet and advertises that subnet into EIGRP. Let’s say that R2’s metric to reach that subnet is 28160. When the subnet is advertised to R1, R2 informs R1 that its metric to reach is 10. From the R1’s perspective that metric is considered to be the reported distance for that route. R1 receives the update and adds the metric to the neighbor to the reported distance. That metric is called the feasible distance and is stored in R1’s routing table (30720 in our case).

The feasible and reported distance are displayed in R1’s EIGRP topology table:

Successor and feasible successor

Another two terms that appear often in the EIGRP world are successor and feasible successor. A successor is the route with the best metric to reach a destination. That route is stored in the routing table. A feasible successor is a backup path to reach that same destination that can be used immediately if the successor route fails. These backup routes are stored in the topology table.

For a route to be chosen as a feasible successor, one condition must be met:

the neighbor’s advertised distance (AD) for the route must be less than the successor’s feasible distance (FD).

The following example explains the concept of a successor and a feasible successor.

R1 has two paths to reach the subnet The path through R2 has the best metric (20) and it is stored in the R1’s routing table. The other route, through R3, is a feasible successor route, because the feasiblility condition has been met (R3’s advertised distance of 15 is less than R1’s feasible distance of 20). R1 stores that route in the topology table. This route can be immediately used if the primary route fails.

EIGRP topology table

EIGRP toplogy table contains all learned routes to a destination. The table holds all routes received from a neighbor, successors and feasible successors for every route, and interfaces on which updates were received. The table also holds all locally connected subnets included in an EIGRP process.

Best routes (the successors) from the topology table are stored in the routing table. Feasible successors are only stored in the topology table and can be used immediately if the primary route fails.

Consider the following network topology.

EIGRP is running on all three routers. Routers R2 and R3 both connect to the subnet and advertise that subnet to R1. R1 receives both updates and calulates the best route. The best path goes through R2, so R1 stores that route in the routing table. Router R1 also calculates the metric of the route through R3. Let’s say that advertised distance of that route is less then feasible distance of the best route. The feasibility condition is met and router R1 stores that route in the topology table as a feasible successor route. The route can be used immediately if the primary route fails.

Configuring EIGRP 1

EIGRP configuration closely resembles RIP configuration. Only two steps are required:

enabling EIGRP by using the router eigrp ASN_NUMBER command

telling EIGRP which networks to advertise by using one or more network statements

The first command, router eigrp ASN_NUMBER, enables EIGRP on a router. ASN_NUMBER represents an autonomous system number and has to be the same on all routers running EIGRP, otherwise routers won’t become neighbors. The second command, network SUBNET, enables EIGRP on selected interfaces and specifies which networks will be advertised. By default, the network command takes a classful network number as the parameter.

To illustrate a configuration of EIGRP, we will use the following network:

eigrp sample topology

The network depicted above consists of only two routers. Each router has a directly connected subnet that needs to be advertised through EIGRP. The following figure show the EIGRP configuration on R1 and R2:

eigrp r1 configuration
eigrp r2 configuration

You can verify that routers have become neighbors by using the show ip eigrp neighbors command on either router:

show ip eigrp neighbors

The command above lists all EIGRP neighbors. The address field lists the neighboring router RID (router ID). The interface field shows on which local interface the neighbor relationship has been formed.

You can verify that routes are indeed being exchanged by using the show ip route command on both routers:


eigrp r1 show ip route


eigrp r2 show ip route

The D character at the beginning of a line in a routing table indicates that the route has been learned via EIGRP.

Configuring EIGRP 2

By default, the network command uses a classful network as the parameter. All interfaces inside that classful network will participate in the EIGRP process.To enable EIGRP only on specific interfaces, a wildcard mask can be used. The syntax of the command is:

(router-eigrp) network WILDCARD_MASK

Consider the following example.

eigrp sample topology 2

Router R1 has two directly connected subnets, and We want to enable EIGRP only on the subnet connected to the interface Fa0/0. If we enter the network command under the EIGRP configuration mode, both subnets will be included in EIGRP process because we’ve used a classful network number in the network command. To configure EIGRP only on interface Fa0/0, the network command can be used. This will enable EIGRP only on interfaces starting with 10.0.0.X.

eigrp wildcard mask

By using the command show ip protocols, you can verify that only the network is included in  EIGRP:

show ip protocols eigrp

Hope this article helpful for you. Thank You

Indian Cyber Army | Make IT Secure

Enjoy…Stay Happy…Stay Secure…

Hope this article helpful for you. Thank You

If You Appreciate What We Do Here On Hackonology, You Should Consider:

Hackonology is the fastest growing and most trusted community site where you can find lots of courses, articles about Technology/Hacking/Cracking. Millions of people visit Hackonology! to search or browse the thousands of published articles available FREELY to all.

Let's be a part of Hacker's Community! Join our Hacking Team

We Are Indian We Are Great